Metric Specifications

Click the tabs below to cycle between specifications.

General Specifications
Model	HB 600	HB 800	HB 1000
Body Capacity	5.5 m	7.3 m	9.1 m
Hopper Capacity	1.4 m³	1.4 m³	1.4 m³
Body Width (inside)	152.4cm	152.4cm	152.4cm
Body Width (outside) (A)	238.8cm	238.8cm	238.8cm
Body Length (B)	350.5cm	419.1cm	477.5cm
Body Height (C)	203.2cm	203.2cm	203.2cm
Overall Body Height (tailgate raised)	317.5cm	317.5cm	317.5cm
Approx. Body Weight * (Empty & Exclusive of Options)	2068.4 kg	2426.7 kg	2744.2 kg
Average Compaction	272-363 kg/m	272-363 kg/m	272-363 kg/m

Hydraulic Cylinder Specifications
Model	HB 600	HB 800	HB 1000
Ejection Panel (1) 4-Stage Telescopic	16.5cm; 205.7cm Stroke	16.5cm; 289.6cm Stroke	16.5cm; 350.5cm Stroke
Tailgate Cylinders (2)	6.4cm X 142.2cm X 3.8cm	6.4cm X 142.2cm X 3.8cm	6.4cm X 142.2cm X 3.8cm
Body Lift Cylinders (2)	8.9cm X 35.6cm X 4.4cm	8.9cm X 35.6cm X 4.4cm	8.9cm X 35.6cm X 4.4cm

‡ - Length measured depends on options ordered.

* - Approximate Body Weight empty and exclusive of options.

** - Any Chassis sent to Scranton Manufacturing with less than the minimum guideline requirements will not be mounted. (Chassis must be capable of carrying the net weight of the body plus the weight of the refuse collected.)

Mamba Body Construction Specifications

Click the panels below to expand the desired specifications.

Body Specs

Main Body Rails	C6 x 8.2# Channel
Hopper Floor	All Models - 0.6cm 50K
Body Floor	HB800, HB1000, 26.5L	A36
Floor Braces	0.5cm x 5.1cm x 15.2cm	A500B Tube
Mounting Brackets	Formed 0.6cm A36 Plate
Ejection Panel Tracks	C6 x 8.2# Channel
Body Side Walls	Lower 37.9L; Upper 45.4L	50K; A569
Roof	45.4L	A569
Rear Frame Top & Sides	0.6cm x 7.6cm x 7.6cm	A500B Tube
Rear Frame Lower	0.6cm x 7.6cm x 7.6cm	A500B Tube
Tailgate Hinge Lugs	1.3cm	A36
Access Door	27.94 x 86.36 Door Size

Tailgate Specs

Tailgate	37.9L	AR235 GR
Tailgate Capacity	0.5m³
Tailgate Inside Height	213.4cm
Tailgate Inside Width	152.4cm
Tailgate Hopper Bubble	37.9L 50K
Tailgate Sides	37.9L 50K
Tailgate Seal Height	53.3cm
Tailgate Hinge Lugs	1.3cm	A36

Ejection Panel Specs

Base & Support Structure	Formed 0.6cm	A36
Bottom Face Sheet	Formed 1cm	A36 Plate
Shoes/Wear Pads	(2) 0.6cm x 14.6cm x 61cm	UHMW
Cylinder Supports	1.9cm	A36 Plate
Cylinder Pin	(1) 0.6cm I.D. 1144 Stress proof

Hydraulic System Specs

Operating Pressure	1,800 PSI	12,410 KPA
Min. Accept. Oil Flow	17 GPM	64 LPM
Pump Flow	20 GPM	75 LPM
Tank Capacity	24gal with 100 Mesh 141 micron suction strainer	91 L
Packer Cycle Time	19 sec
Hydraulic Hoses	4 to 1 burst
Filter	10 micron
Engine RPM	1,275 - 1,550

Looking for Standard conversions of the specs? View them here →